JUMPFORCE PRO - Instructions Guide

WE ARE SO MUCH MORE THAN JUST A BRAND

Before ToolTroopers was a brand, we were just two brothers in a garage with our dad.

We didn’t grow up watching from the sidelines. We grew up holding the light steady while he worked. Sometimes he’d hand us a wrench. Sometimes he’d just say “Don’t move.”

It wasn’t really about fixing cars.

It was about discipline. Patience. Pride.

About learning that problems don’t fix themselves, and that being prepared is a way of taking care of the people you love.

Those lessons stayed with us.

Today, they guide everything we build.

We design tools for parents, drivers, families, and problem-solvers, because when something goes wrong, it’s rarely just about the tool. 

It’s about getting home safely. It’s about stepping up when it matters.

JumpForce Pro was built with that responsibility in mind.

Strong. Dependable. Long-lasting.

Not made for quick wins. Made to earn its place in your vehicle and stay there for years.

That’s who we are.
And that’s why JumpForce Pro exists.

From our garage to yours,
Martin & Philip
Founders, TOOLTROOPERS 

Your garage, your rules.
We just bring the tools.

Safety First (Read Before Use)

DANGER: Failure to follow these safety instructions may result in electrical shock, explosion, fire, serious injury, death, or property damage. Use this product only as intended.

• Inspect before use. Do not use the jump starter if the unit, cables, clamps,
• ports are damaged or if there is any swelling, leakage or odor.
• Keep clear of moving engine parts (fans, belts, pulleys) and hot surfaces.
• Wear eye protection when working near batteries. Battery acid can cause serious injury, flush with clean water and seek medical help if exposed.
• Do not smoke or use sparks/open flames near a battery.
• Do not allow input/output ports to get in contact with metal objects.
• Use in a well-ventilated area. Lead-acid batteries can produce explosive gases.
• Do not jump-start a damaged, leaking, or frozen battery.
• Do not allow the clamps to touch each other once connected to the jump starter.
• Keep out of reach of children.
• Do not submerge in water or expose to heavy rain with open ports. Keep ports closed when not in use.
• Do not disassemble, crush, puncture, or incinerate the unit or clamps.
• Do not cover the product during use or charging (risk of overheating).
• Secure the unit if stored in a vehicle trunk so it cannot roll and create a driving hazard.
• Use only within the specified temperature ranges.
• Do not charge in any other way than as described in the instructions.
• Do not overcharge, over-discharge, reverse charge, or short-circuit the jump output.
• Recharge preferable once every four to three months; at minimum once every five months.
• Do not use the device for Jump Starting if the device is below 25% battery, as it will damage the device.
• Dispose of the built-in battery according to regulations, do not dispose of it as household waste.
  

This jump starter is designed for 12V vehicles with a negative ground system (most common) and for use with a 12V lead-acid vehicle battery. If you are unsure about the battery type, consult a professional.

What’s in the box

• JumpForce Pro - Main Device
• JumpForce Pro - Smart Clamps
• Premium USB-C Fast Charging Cable
• Premium Fast Charge Wall Adapter
• Storage Bag
• User Manual

Product Overview - JUMPFORCE PRO Main Device

1. Power Button
2. USB-A Output Fast Charging (QC3.0)
3. USB-C Input & Output Ultra Fast Charging (PD 60W)
4. Battery Level Indicator
5. Smart Clamp Device Port (EC5)
6. LED Flashlight Button
7. LED Flashlight
   

 

Product Overview - Smart Clamp Device

1. Red Clamp (+ Positive Terminal)
2. Black Clamp (- Negative Terminal)
3. Boost Ready & Standby Indicator
4. Error Indicator
5. Override Button “Force Start”
6. Smart Clamp Device Connector (EC5)

Register for Our Free Recharge Reminder Service

Sign up for our free recharge reminder for your JUMPFORCE PRO.

We’ll send you a simple reminder every 3 months to help keep your jump starter charged and ready.

Always remember to recharge your JUMPFORCE PRO after using it, so it’s ready whenever you need it.

REGISTER NOW

You can also go to: https://tooltroopers.com/jfp-rrs

 

 

Instructions to JUMPFORCE PRO

Step 1: Charge the JUMPFORCE PRO

Before First Use

Fully charge the JUMPFORCE PRO before using it for the first time. This ensures maximum performance and long-term battery health. 

We recommend charging for 3 hours the first time. Thereafter each charge only takes 30-45 minutes for a full charge, if a compatible fast charging cable and adapter is being used.

Charging via USB-C (Recommended)

1. Connect the included USB-C charging cable to the USB-C port on the jump starter.
   
   
2. Connect the other end of the cable to a USB wall charger adapter or USB power outlet.
   
   
3. Plug the charger into a power outlet. Charging will begin automatically (The Battery LED will start to blink.).
   
   
4. The Jump Starter is fully charged when the LED lights turn off.
   
   

The JUMPFORCE PRO supports USB-C Power Delivery (PD) fast charging up to 60W when used with a compatible charger / adapter.

Charging via Vehicle (Car Charging)

1. Connect the USB-C charging cable to the jump starter.
   
   
2. Plug the cable into a vehicle USB or USB-C power port.
   
   
3. Charging will begin automatically while the vehicle is powered.
   
   
4. The Jump Starter is fully charged when the LED lights turn off.
   
   

Vehicle charging is slower than wall charging and is best used for topping up rather than full charging.

Typical Charging Times (Approximate)

Charging time depends on the charger / adapter used:

• 60W PD charger: 0.6 ± 0.3 hours (30-40 minutes)
• 18W fast charger: 4 ± 0.5 hours
• 5V / 2A charger: 5 ± 2 hours
• 5V / 1A charger: 10 ± 2 hours

Charging times may vary depending on temperature and power source.

Battery Level Display

• Press the Power Button to display the current battery level.
  
  
• Battery indicator lights show the remaining charge.
  • 25% 50% 75% or 100%
    
    
• When charging is complete, the battery indicators will stop flashing and turn the LED lights off.
  
  

Charging Temperature & Safety

• Charging temperature range: 0°C to +45°C (32°F to 113°F)
  
  
• If the unit is too hot or too cold, charging protection will activate.
  
  
• In this case, allow the unit to return to a normal temperature and charging will resume automatically.

 

Step 2: Jump Starting a Vehicle

Before You Begin

1. Confirm the vehicle uses a 12V lead-acid battery
   
   
2. Turn OFF all electrical loads (headlights, radio, HVAC, etc.)
   
   

⚠️ Important Use Limitations

• For 12V vehicles only
  
  
• Gasoline engines: up to 6.0L
  
  
• Diesel engines: up to 3.0L
  
  
• Do not use on vehicles with higher-voltage systems
  
  

Jump-Starting Instructions

Check Battery Level Before Use.

Turn on the jump starter to check the battery level. For reliable starting performance, the battery level should be above 50%. If the battery level is 25% or below, recharge the unit before use.

1. Remove the protective caps and firmly insert the Smart Clamp Device (EC5) Connector into the Smart Clamp port on the main unit.
   
   
2. onnect the RED clamp to the battery positive (+) terminal.
   
   
3. Connect the BLACK clamp to the battery negative (–) terminal
   (or a clean, unpainted chassis ground if recommended by your vehicle manufacturer).
   
   
4. Hold the Power Button down for 2 seconds to turn on the JUMPFORCE PRO.
   
   
5. Wait for the smart clamp to indicate READY (green light on).
   - If the smart clamp blinks green or red, and makes any buzz / beeps, go to the Error Indication overview.
   
   
6. Start the vehicle.
   - If it does not start, wait 30–60 seconds before trying again.
   - Do not exceed three attempts. (If it doesn’t start after three attempts, redo the process. If it won’t start, the problem may not be your car battery.) 
   
   
7. Once the vehicle starts, check the Jump Start is turned off and remove the clamps in reverse order:
   - BLACK clamp first, then RED clamp
   - Disconnect the Smart Clamp Device (EC5) from the main unit
   
   

Important Notes

• Allow the unit to cool between attempts.
  
  
• Do not leave clamps connected after starting

Automatic Safety Timeout

• The smart clamp automatically cuts off output after 90 seconds.
  
  
• If this occurs, make sure the unit is powered off, disconnect the clamps, and restart the process.
  
  

Error Indication

• If the red warning light flashes or an alarm sounds on the Smart Clamp Device, stop immediately.
  
  
• Take note of the red and green lights and buzzer. Are the red and green light stable, does it blink, does the buzzer sound every second or every other?
  
  
• Power off the unit, disconnect the clamps, and refer to the “Indications / Errors Overview” section below to identify and resolve the issue before continuing.
  

Indications & Errors Overview

If the jump starter or smart clamp displays a warning light or sounds an alarm, refer to the table below before continuing.

When to Use Force Start (the Override Button)

The override button is designed for emergency use only.

The override button should only be used when the vehicle battery is completely discharged and the smart clamp cannot detect it automatically. Use with caution and only after confirming correct clamp connection and the car is in normal condition without any signs of short circuit.

WARNING: Short circuit may cause explosion.

Use it only if ALL of the following are true:

• The vehicle uses a 12V lead-acid battery
  
  
• The clamps are correctly connected (RED to +, BLACK to –)
  
  
• The jump starter has sufficient charge (Click the start button to verify, needs at least 50% / 2 bars).
  
  
• The vehicle battery is extremely low or fully depleted
  
  
• The smart clamp does not indicate READY (green light does not appear) or any Red Errors.
  
  

In these situations, the vehicle battery voltage may be too low for the smart clamp to detect automatically. The override function allows the jump starter to temporarily bypass battery detection and deliver power directly.

How to Use Force Start (Emergency Only)

1. Plug the smart clamp EC5 connector fully into the jump start output port.
   
   
2. Connect the RED clamp to the battery positive (+) terminal.
   
   
3. Connect the BLACK clamp to the battery negative (–) terminal
   (or a clean, unpainted chassis ground if recommended by your vehicle manufacturer).
   
   
4. Hold down the Power Button to turn on the JUMPFORCE PRO.
   
   
5. Press and hold the override button on the smart clamp for 5 seconds.
   
   
6. When the indicator shows override mode (green light), start the vehicle immediately.
   
   
7. Once the vehicle starts. Make sure the Jump starter is turned off and remove the clamps in reverse order:
   
   - BLACK first, then RED.
   
   

⚠️ Important: Override mode is active for a limited time only. If the vehicle does not start, stop and allow the unit to reset (Turn it off for 1 minute) before attempting again.

Important Safety Notes

• Do not use override mode for routine jump starts
  
  
• Do not use on vehicles with damaged batteries
  
  
• Do not use if clamps are connected incorrectly
  
  
• Override mode bypasses the safety protections and must be used carefully
  
  

If the override function does not start the vehicle, the issue may not be the battery.

The Power Bank Function & How to Use it

The JUMPFORCE PRO can also be used as a portable power bank to charge phones, tablets, and other USB-powered devices.

How to Charge Your Devices

1. Hold down the Power Button to turn on the jump starter.
   
   
2. Do not connect the smart clamp (EC5 cable) while using the power bank function.
   
   
3. Connect your device using the included USB fast charging cable or other compatible cable:
   - Use the USB Output port, or
   - Use the USB-C input/output port
   
   
4. Charging will start automatically.
   
   

The JUMPFORCE PRO supports fast charging and can charge compatible devices up to 75% faster than a standard charger.

Important Power Bank Notes

• We do not recommend using the power bank function when the battery level is below 50%, if you are not heading somewhere you can recharge the unit. Maintaining enough charge helps ensure the jump starter is ready if your vehicle battery runs out unexpectedly.
  
  

• After using the jump starter as a power bank, fully recharge the unit when you return home to ensure it’s ready for your next drive.

The LED Flashlight & How to Use it

The JUMPFORCE PRO includes a built-in LED flashlight for roadside use, emergencies, and low-light situations.

How to Use the Flashlight

1. Hold down the Start Button
   
   
2. Press the Light Button to turn the flashlight ON.
   
   
3. Press the Light Button again to cycle through the light modes:
   - 100%
   - Blink
   - SOS
   
   
4. Press the Light Button once more to turn the flashlight OFF.

Important Flashlight Notes

• The flashlight can operate independently of the jump-starting function.
  
  
• When fully charged, the flashlight can provide up to 35 hours of continuous use.
  
  
• Use the SOS mode only in emergency situations where visibility or signaling is required.

Storage & Maintenance

Proper storage and basic maintenance help ensure your JUMPFORCE PRO is always ready when you need it.

Storage Guidelines

• Store the jump starter in a cool, dry place away from direct sunlight, heat, or moisture.
  
  
• Storage temperature: 
  • Short-term: -4°F to 140°F (-20°C to +60°C)
    
  • Long-term: 32°F to 95°F (0°C to +35°C)
    
    
• Avoid storing the unit in extremely hot or cold environments for extended periods.
  
  
• Do not store the jump starter with the smart clamp device (EC5) connected.
  
  
• Keep the unit and accessories clean and protected when not in use.
  

 

Battery Care

• For long-term storage, maintain the battery level at +50%.
  
  
• Recharge the jump starter every 3-4 months if it has not been used.
  
  
• Do not store the unit fully discharged for extended periods, as this may reduce battery life.
  
  

After Use

• After jump-starting a vehicle or using the unit as a power bank, recharge the jump starter as soon as possible.
  
  
• Inspect the clamps and cables for dirt, damage, or corrosion before storing.
  
  

General Maintenance

• Keep the charging ports and connectors free of dust and debris.
  
  
• Clean the exterior with a dry or slightly damp cloth.
  
  
• Do not use solvents, chemicals, or abrasive cleaners.
  
  
• Do not disassemble or attempt to repair the unit yourself.

TOOLTROOPERS Contact Information

Do not hesitate to contact us, with any questions or concerns.
You can reach us at support@tooltroopers.com, we usually get back to you within 24 hours (Mon-Fri).

Technical Specifications (Summary)

Product Name:  JUMPFORCE PRO 50

Model:  JFP50

Battery Type:  Built-in high-rate polymer lithium battery pack

Peak Current:  1000A

Internal Battery:  29.6 Watt-Hour Lithium Ion

Jump-Start Output Port:  EC5 (DO port)

USB-A Output: QC 3.0
   - 5V3A  9V2A 12V1.5A

USB-C Input / Output: USB-C Power Delivery (PD), bidirectional
   - 5V / 9V / 12V / 15V / 20V - up to 3A
   - Maximum output: 60W

Flashlight: Integrated LED strip light
   - Brightness: approx. 150 lumens
   - Modes: 100%, Blink, SOS, Off

Operating Temperature:
   - Discharge: −20°C to +60°C
   - Charging: 0°C to +45°C
   - Jump starting: −30°C to +60°C

Storage Temperature:
   - −20°C to +60°C (short-term)
   - 0°C to +35°C (long-term)

Humidity Range:
   - Operating: 20–80% RH
   - Storage: 10–90% RH

Protection Rating:
IP66 (With ports closed)

Cooling:
Natural Convection

Drop Resistance:
Tested for drops up to 3 meters

Crush Resistance:
Withstands vehicle load up to 3.0 tons

Dimensions (L × W × T):
7.09” x 4.05” x 2.32” | 180 × 103 × 50 mm

Weight:
1.45 lb (±0.04 lb) | 660 g (±20 g)

Battery Cycle Life:
Up to 800 charge cycles

Standby Power Consumption:
≤70 mA

Hibernation Power Consumption:
≤200 µA

Typical Charging Time (approximate):
60W USB-C PD charger: 0.6 ± 0.3 hours
18W fast charger: 4 ± 0.5 hours
5V / 2A: 5 ± 2 hours
5V / 1A: 10 ± 2 hours

Limited Warranty

TOOLTROOPERS (“the Company”) warrants that the JUMPFORCE PRO portable jump starter (“the Product”) is free from defects in materials and workmanship under normal and intended use for a period of twenty-four (24) months from the date of original retail purchase (“Warranty Period”).

This Limited Warranty applies only to the original end-user purchaser and is non-transferable.

Warranty Coverage

During the Warranty Period, if the Product is determined by the Company to be defective due to materials or workmanship, the Company will, at its sole discretion:

• Repair the Product; or
• Replace the Product with a new or refurbished unit of equal or comparable value.

Replacement products or parts may be new or refurbished and are warranted only for the remainder of the original Warranty Period.

Exclusions and Limitations

This Limited Warranty does not cover damage, defects, or failure resulting from, but not limited to:

1. Improper use, misuse, abuse, negligence, or improper storage
   
   
2. Failure to follow instructions provided in the user manual
   
   
3. Unauthorized modification, disassembly, repair, or alteration
   
   
4. Use with incompatible chargers, accessories, or power sources
   
   
5. Electrical faults caused by incorrect vehicle voltage or polarity
   
   
6. Accidental damage, impact, crushing, or exposure to excessive heat
   
   
7. Water or moisture damage beyond the Product’s specified protection level
   
   
8. Normal wear and tear, cosmetic damage, or battery degradation over time
   
   
9. Acts of God or force majeure, including fire, flood, lightning, or earthquake
   
   
10. Products purchased from unauthorized sellers or resellers
    
    

Warranty Claim Procedure

To initiate a warranty claim, the original purchaser must contact the Company through its official support channels and provide:

1. Proof of purchase (receipt or order confirmation)
   
   
2. Product model and serial number (if applicable)
   
   
3. A detailed description of the defect
   
   
4. Photographs or video evidence, if requested
   
   

The Company reserves the right to request return of the Product for inspection prior to approving any warranty claim.

Limitation of Liability

To the maximum extent permitted by applicable law, the Company shall not be liable for any indirect, incidental, special, or consequential damages, including but not limited to loss of use, loss of time, inconvenience, or vehicle-related damages, arising from the use or inability to use the Product.

The Company’s total liability under this Limited Warranty shall not exceed the original purchase price of the Product.

Disclaimer of Implied Warranties

Except as expressly stated herein, the Company disclaims all other warranties, express or implied, including but not limited to any implied warranties of merchantability or fitness for a particular purpose, to the extent permitted by law.

Some jurisdictions do not allow limitations on implied warranties or the exclusion of incidental or consequential damages. In such cases, the above limitations may not apply.

Governing Law

This Limited Warranty shall be governed by and construed in accordance with the laws of the jurisdiction in which the Product was purchased, without regard to conflict of law principles.

Consumer Rights

This Limited Warranty grants you specific legal rights. You may have additional rights that vary depending on your state, country, or jurisdiction.